MUTOH Rockhopper II Series Especificaciones Pagina 267
- Pagina / 319
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Rockhopper II series printers – Maintenance Manual
268
AP-74065, Rev. 1.2, 27/09/04
9.2.1. Operating condition display
This chapter explains the messages displayed, the items to be confirmed and the remedy.
No. Message Phenomenon Check point Action Refer to
(1) Check if the
cover R/L sensor
assembly comes
on and off properly
when the front
cover is opened
and closed.
• Adjust the
operating position
of the cover sensor
R/L assembly.
→ Cover sensor
adjustment
(2) Make sure that
cables for the
cover sensor
assembly are
securely
connected.
• Securely connect
the cables for the
cover sensor
assembly to
connectors J155
and J156 on the
mainboard
assembly.
• Securely connect
the cover L sensor
to the cover L
cable.
→ Replacing the
Mainboard
assembly,
HDD_Extension
board assembly,
HEAD_DRV
board assembly
and cooling fan
assembly.
→ Cover sensor
adjustment
1 Cover Open The front cover is
open.
(3) The Mainboard
assembly may
have a problem.
• Replace the
Mainboard
assembly.
→ Replacing the
Mainboard
assembly,
HDD_Extension
board assembly,
HEAD_DRV
board assembly
and cooling fan
assembly.
(1) Check the
operation of the
transmission
photosensor for
the lever up/down
via “Test:Sensor”
of the self-
diagnostic
function.
• Replace the
transmission
photosensor at the
lever.
→ Replacing the
transmission
photosensor.
(2) Make sure the
transmission
photosensor at the
lever motor has
been securely
installed.
• If the
transmission
photosensor is
detached, fix it
securely.
→ Replacing the
transmission
photosensor.
2 Set Paper The lever is up
(3) Check the
sensor element of
the transmission
photosensor at the
lever motor for
contamination.
• Clean the sensor
element using
cotton swabs.
→ Replacing the
transmission
photosensor.
- Maintenance Manual 1
- COPYRIGHT NOTICE 4
- Important Notice 6
- TABLE OF CONTENTS 8
- AP-74065, Rev. 1.2, 27/09/04 10
- 1. SAFETY INSTRUCTIONS 14
- 1.3.2. Caution 15
- 1.4. WARNING LABELS 16
- (2) Back Part 18
- Ink Type 19
- 2. PRODUCT OVERVIEW 20
- 2.3.1. Front 21
- 2.3.2. Back 22
- 2.3.3. Operation panel 23
- 2.4. PRINTER STATUS 25
- 2.4.5. Selecting Language 26
- 2.5.3. 2 or 4 heater 28
- 3. SPECIFICATIONS 30
- 3.4. INSTALLATION 34
- 4. PARTS REPLACEMENT 36
- 4.2. REMOVING THE COVER 37
- 4.2.2. Removing side cover R 39
- 4.2.3. Removing side cover L 41
- 4.4. REPLACING BOARD BASES 64
- cable assembly 71
- assembly 77
- Step 1 : Unlock the head 85
- 4.6.4. Replacing the T fence 88
- 4.7. REPLACING THE CURSOR 95
- Step 12 : Cap once 113
- maintenance home position) 118
- 4.9. REPLACING THE PUMP AREA 119
- 5. SELF-DIAGNOSIS FUNCTION 136
- 5.2.2. Starting Up 137
- 5.4. TEST / INSPECTION MENU 141
- 5.4.1. RAM Capacity Menu 142
- 5.4.2. Version Menu 142
- 5.4.3. Operation Panel Menu 143
- 5.4.4. Sensor Menu 144
- 5.4.5. Encoder Menu 145
- 5.4.6. Fan Menu 146
- 5.4.7. History Menu 146
- (2) Serious error history 147
- 5.4.8. Head Signal Menu 148
- 5.5. ADJUSTMENT MENU 149
- 5.5.1. Skew Check Menu 150
- 5.5.2. Head rank input menu 151
- 5.5.4. Head Slant Check Menu 154
- 5.5.4.2. Front and back 158
- For a 8 head machine 161
- 5.5.10. Test print menu 169
- 5.5.11. Head wash menu 170
- 5.5.14. Fill printing menu 173
- 5.6. PURGE MENU 174
- 5.7. SAMPLE PRINTING MENU 175
- 5.8. PARAMETER MENU 176
- 5.8.2. Parameter Update Menu 177
- (1) Head ID 178
- (4) Media feed distance 180
- (5) Mechanical parameter 181
- (6) Ink parameter 182
- (7) Ink ID mask 182
- (8) Serial number entry 183
- 5.9. ENDURANCE RUNNING MENU 184
- 5.9.3. Cutter Endurance menu 187
- 5.9.6. Pump Endurance menu 190
- 5.10. HEAD LOCK MENU 195
- 5.11. HEATER SYSTEM MENU 196
- 5.11.3. Heater Test 30 Menu 197
- 5.11.4. Heater Test 50 Menu 197
- 5.11.5. Heater Test Max Menu 197
- 5.11.6. Heater Version Menu 198
- 5.11.7. Heater Adjust Menu 198
- 5.12. ECO PREPARE MENU 199
- 6. MAINTENANCE MODE 202
- 6.3. MAINTENANCE MENU 203
- Head Voltage 207
- 7. ADJUSTMENTS 208
- Cutter adjustment 209
- Sub-platen 209
- Cutter Endurance menu 209
- 7.3. PARAMETER BACKUP 211
- 7.4. FIRMWARE INSTALLATION 214
- (2) When using a computer 215
- 7.5.2. Adjustment Procedure 217
- 7.6.2. Adjustment Procedure 219
- 7.7.1 Head slant adjustment 220
- 7.7.1.2 For a 8 head machine 222
- 7.7.2.1 For a 4 head machine 224
- 7.10.2. Adjustment Procedure 231
- 7.12. HEAD HEIGHT ADJUSTMENT 233
- 7.13.2. Adjustment Procedure 235
- 7.14. CUTTER ADJUSTMENT 238
- (1) For 50 or 64 inch spec 239
- (2) For 87 inch spec 240
- 7.16. BOARD CHECKLIST 247
- 7.16.2. Control board 248
- 7.16.3. Power board 249
- Heater Elements 249
- 7.16.5. Checklist 251
- 8. MAINTENANCE 256
- 8.2. CLEANING 257
- 8.3. PERIODICAL SERVICES 258
- 8.4. PART LIFE INFORMATION 260
- 8.5. JIG AND TOOL LIST 261
- 8.6. LUBRICATION/BONDING 262
- 9. TROUBLESHOOTING 266
- 9.2.2. Message type errors 269
- 9.2.3. Heating system error 276
- 9.2.4. Data error 277
- 9.2.5. Command errors 278
- NOT DISPLAYED 290
- 9.3.7. Other problems 315
- 10. APPENDIX 316
- VIEWS/CONFIGURATION DIAGRAMS 317
Relacionado con productos y manuales para Impresión y escaneo MUTOH Rockhopper II Series
(66 paginas)
Impresión y escaneo MUTOH RJ600EX-B-01 Guía de usuario
(100 paginas)
(100 paginas)
Impresión y escaneo MUTOH RJ600EX-B-01 Guía de usuario
(110 paginas)
(110 paginas)
Impresión y escaneo MUTOH PJ-2216NXE Guía de usuario
(266 paginas)
(266 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales